Caspase‑3 Colorimetric Activity Assay Kit (Cat. No. AK0689).

2026-10-26

Questions & answers
Caspase‑3 Colorimetric Activity Assay Kit (Cat. No. AK0689).
We are planning a study of doxorubicin-induced cardiotoxicity in male rats and am considering your Caspase‑3 Colorimetric Activity Assay Kit (Cat. No. AK0689).
Please find our answers below — note that points 1–4 refer to our Caspase-3 colorimetric activity assay kit (DEVD-pNA substrate, 405 nm), and point 5 addresses your caspase-1 requirement.
1Is the kit validated for rat heart tissue homogenate?
The datasheet states the kit is suitable for mammalian tissue and cell samples. There is no rat-heart-specific validation claim in the datasheet, but rat heart is a mammalian tissue and is within the intended sample scope. Recommended tissue protocol: homogenise at 1 g tissue : 5–10 mL of Reagent II (e.g. ~0.1 g tissue in 1 mL), ice-bath homogenisation, stand on ice 15 min, centrifuge at 4 °C for 10–15 min, and use the supernatant. As the datasheet advises, we recommend a pre-test with 2–3 samples before running the full set.
2Can the assay be run in a 96-well microplate with an absorbance reader at 405 nm?
Yes. The datasheet specifies a spectrophotometer or microplate reader, a 100 μL cuvette or 96-well plate, wavelength 405 nm, reaction volume 100 μL per well, incubated at 37 °C for 60–120 min (can be extended if colour development is weak).
3For 25 rat samples in duplicate, which kit size? Do the stated test numbers include standards and blanks?
25 samples × 2 replicates = 50 reaction wells, plus 1–2 blank wells and 6 standard concentrations (0, 12.5, 25, 50, 100, 200 μmol/L) → about 57–58 wells. We recommend the 100T size (20T and 50T would not be sufficient). The stated test number refers to sample reaction wells only — standards and blank wells are in addition.
•  4) Can results be reported as caspase-3 activity per mg protein (U/mg) using Bradford, following the sample dilution in the manual?
Yes, this kit measures caspase-3 activity directly. The datasheet gives: Caspase-3 activity (U/mg prot) = x × V_R ÷ (V_S × Cpr) ÷ T × 10³ = 2x ÷ Cpr ÷ T where x = pNA concentration read from the standard curve (μmol/L), V_R = 0.1 mL, V_S = 0.05 mL, Cpr = sample protein concentration (mg/mL), T = reaction time (h). Two important points from the datasheet: dilute the sample 2-fold with distilled water before the Bradford assay (Reagent II contains DTT, which interferes with protein determination), and BCA is not recommended for protein quantification with this kit.
•  5) Colorimetric caspase-1 activity assay with an Ac-YVAD-pNA substrate, rat heart tissue, 405 nm microplate reading?
Yes, we offer this as a separate kit — the caspase-1 colorimetric activity assay kit uses YVAD-pNA (Ac-YVAD-pNA) as substrate, measures pNA at 405 nm, and is likewise intended for mammalian tissue and cell samples. So both options are available from us:
Caspase-3 – DEVD-pNA substrate, 405 nm → the kit discussed in points 1–4
Caspase-1 – YVAD-pNA substrate, 405 nm Both are supplied in 20T / 50T / 100T sizes.
Related questions
SUNLONG BIOTECH CO., LTD · Hangzhou, China · all contact details
GB/T 19001-2016 / ISO 9001:2015 · For research use only

Leave a message

* To protect against spam, please pass the CAPTCHA test below.

Newsletter

Sign up