Details
| Culture Medium | Yeast extract powder: 3.0g, Malt extract: 3.0g, Glucose: 10.0g, Casein peptone: 5.0g, Agar: 20.0g, pH: 6.2±0.2 (25℃) |
| Growth Conditions | Culture temperature 30℃; Culture time 24-48 hours; Gas environment aerobic; |
| Storage Conditions | 2-8℃ |
| Morphology | Colony diameter 1-2mm, round, regular edges, opaque, milky white front, raised center, smooth surface, bright surface, viscous texture, moist texture, G+ (blue-purple), cocci, purity: pure |
| Isolation Source | Nail infection |
| Procedure | Before use, add anhydrous ethanol to Buffer GD and Wash Solution PW, refer to the bottle label for volume; 1. Take yeast cells (up to 5×10⁷ cells), centrifuge at 12,000rpm (13,400×g) for 1min, remove supernatant as much as possible (if the bacterial suspension is large, collect cell pellet into one centrifuge tube through multiple centrifugations); 2. Yeast cell wall disruption: Enzymatic method: Add 600μL Sorbitol buffer to the pellet, add approximately 50U Lyticase (self-provided, catalog no.: RT410), mix thoroughly. Treat at 30℃ for 30min. Centrifuge at 4,000rpm (1,500×g) for 10min, discard supernatant, collect pellet. Note: The above is the Lyticase dosage for 5×10⁷ yeast cells; adjust Lyticase concentration and incubation time according to yeast strain and cell count; 3. Resuspend the pellet in 200μL Buffer GA, mix thoroughly. If RNA removal is needed, add 4μL RNase A (100mg/mL) solution (self-provided, catalog no.: RT405-12), vortex for 15sec, let stand at room temperature for 5min; 4. Add 20μL Proteinase K solution, mix; 5. Add 220μL Buffer GB, mix by inverting thoroughly, place at 70℃ for 10min, solution should become clear, briefly centrifuge to remove droplets from tube cap. Note: A white precipitate may form when adding Buffer GB, which usually disappears at 70℃ and does not affect subsequent experiments. If the solution does not become clear, cell lysis may be incomplete, leading to low DNA yield and impure DNA; 6. Add 220μL anhydrous ethanol, mix by inverting thoroughly, a flocculent precipitate may appear, briefly centrifuge to remove droplets from tube cap; 7. Transfer the solution and flocculent precipitate from the previous step into an adsorption column CB3 (placed in a collection tube), centrifuge at 12,000rpm (13,400×g) for 30sec, discard waste liquid, place adsorption column CB3 back into the collection tube; 8. Add 500μL Buffer GD (check if anhydrous ethanol has been added before use) to adsorption column CB3, centrifuge at 12,000rpm (13,400×g) for 30sec, discard waste liquid, place adsorption column CB3 back into the collection tube; 9. Add 600μL Wash Solution PW (check if anhydrous ethanol has been added before use) to adsorption column CB3, centrifuge at 12,000rpm (13,400×g) for 30sec, discard waste liquid, place adsorption column CB3 back into the collection tube; 10. Repeat step 9; 11. Place adsorption column CB3 back into the collection tube, centrifuge at 12,000rpm (13,400×g) for 2min, discard waste liquid. Leave adsorption column CB3 at room temperature for several minutes to completely dry residual wash solution from the adsorption material. Note: This step aims to remove residual wash solution from the adsorption column; ethanol residue in the wash solution can affect subsequent enzymatic reactions (digestion, PCR, etc.); 12. Transfer adsorption column CB3 to a clean centrifuge tube, add 50-200μL Elution Buffer TE dropwise to the center of the adsorption membrane, let stand at room temperature for 2-5min, centrifuge at 12,000rpm (13,400×g) for 2min, collect solution into the centrifuge tube. Note: To increase genomic DNA yield, the collected solution can be reapplied to the adsorption column, let stand at room temperature for 2min, centrifuge at 12,000rpm (13,400×g) for 2min. Elution buffer volume should not be less than 50μL; too small a volume affects recovery efficiency. The pH of the elution buffer greatly influences elution efficiency. If using ddH₂O as eluent, ensure its pH is within 7.0-8.5; pH below 7.0 reduces elution efficiency; DNA products should be stored at -20℃ to prevent degradation; |
| Sharing Method | Public welfare sharing |
? Notes:
Ordering & shipping
Partial purchase records (0)
Leave a message
+86 0571 56623320
[email protected]
+86 18668110335

Scan Wechat Qrcode
