Home > Molecular Biology > Genomic DNA(gDNA) > Genomic DNA from Vibrio cholerae

Genomic DNA from Vibrio cholerae

Genomic DNA from Vibrio cholerae
Total $330

Product Summary

Alias:霍乱弧菌基因组DNA

NO.:SLQC16164

Lead time:1-4days

Product Form:Lyophilized powder;5μg/Vial

concentration:59.4ng/μL

    Number:

Details

Vibrio cholerae Genomic DNA - Basic Information

Culture Medium Beef Extract: 3.0g, Peptone: 10.0g, NaCl: 35.0g, Agar: 15.0g, pH: 7.2–7.4 (25°C)
Growth Conditions 37°C;
18-24h;
Aerobic
Storage Conditions 2-8°C
Procedure Before use, add anhydrous ethanol to Buffer GD and Rinse Solution PW; refer to the bottle labels for the required volumes.
1. Take 1-5ml of bacterial culture, centrifuge at 10,000rpm (11,500×g) for 1min, and remove the supernatant as completely as possible.
2. Add 200μL Buffer GA to the bacterial pellet, and vortex until the pellet is completely resuspended. Note: For Gram-positive bacteria with difficult-to-lyse cell walls, skip step 2 and treat with lysozyme solution for cell wall lysis. The specific method is: add 110μL buffer (20mM Tris, pH8.0; 2mM Na2-EDTA; 1.2% Triton) and 70μL lysozyme solution (50mg/mL, prepared by the user, catalog number: RT401), and incubate at 37°C for 30min or longer. If RNA removal is required, add 4μL RNase A (100mg/mL) solution (prepared by the user, catalog number: RT405-12), vortex for 15sec, and let stand at room temperature for 5min.
3. Add 20μL Proteinase K solution to the tube and mix well.
4. Add 220μL Buffer GB, vortex for 15sec, incubate at 70°C for 10min; the solution should become clear. Briefly centrifuge to remove droplets from the inner lid. Note: A white precipitate may form upon adding Buffer GB, which usually disappears during the 70°C incubation and will not affect subsequent experiments. If the solution does not become clear, cell lysis is incomplete, which may result in low DNA yield and impurities.
5. Add 220μL anhydrous ethanol, vortex thoroughly for 15sec; flocculent precipitate may appear. Briefly centrifuge to remove droplets from the inner lid.
6. Transfer the solution and flocculent precipitate from the previous step into an adsorption column CB3 (placed in a collection tube), centrifuge at 12,000rpm (13,400×g) for 30sec, discard the waste liquid, and place the adsorption column CB3 back into the collection tube.
7. Add 500μL Buffer GD to the adsorption column CB3 (ensure anhydrous ethanol has been added before use), centrifuge at 12,000rpm (13,400×g) for 30sec, discard the waste liquid, and place the adsorption column CB3 back into the collection tube.
8. Add 600μL Rinse Solution PW to the adsorption column CB3 (ensure anhydrous ethanol has been added before use), centrifuge at 12,000rpm (13,400×g) for 30sec, discard the waste liquid, and place the adsorption column CB3 back into the collection tube.
9. Repeat step 8.
10. Place the adsorption column CB3 back into the collection tube, centrifuge at 12,000rpm (13,400×g) for 2min, and discard the waste liquid. Leave the adsorption column CB3 at room temperature for several minutes to completely dry any residual rinse solution from the adsorbent material. Note: The purpose of this step is to remove residual rinse solution from the adsorption column; residual ethanol in the rinse solution can affect subsequent enzymatic reactions (e.g., restriction digestion, PCR).
11. Transfer the adsorption column CB3 into a clean centrifuge tube, add 50-200μL Elution Buffer TE dropwise to the center of the adsorbent membrane, let stand at room temperature for 2-5min, centrifuge at 12,000rpm (13,400×g) for 2min, and collect the solution in the centrifuge tube. Note: The volume of elution buffer should not be less than 50μL; too small a volume will affect recovery efficiency. The pH of the elution buffer greatly impacts elution efficiency. If using ddH2O as the eluent, ensure its pH is between 7.0 and 8.5; a pH below 7.0 will reduce elution efficiency. DNA products should be stored at -20°C to prevent degradation. To increase the yield of genomic DNA, the collected solution can be reapplied to the adsorption column CB3, let stand at room temperature for 2min, and centrifuge at 12,000rpm (13,400×g) for 2min.
Sharing Method Public Welfare Sharing

? Notes:

    1. Storage Conditions:Lyophilized powder should be stored at 2–8°C away from light. After reconstitution or for solution-type products, store at –20°C and avoid repeated freeze-thaw cycles. For short-term frequent use (within 1 week), temporary storage at 4°C is acceptable.
    2. Reconstitution Method:Prior to use, briefly centrifuge the lyophilized powder (e.g., 12,000 rpm for 1 minute) to collect the DNA at the bottom of the tube. It is recommended to dissolve in sterile TE buffer (pH 8.0) or sterile ddH₂O (pH 7.0–8.5). Mix gently; avoid vigorous vortexing.
    3. Contamination Prevention:Gloves must be worn during operation. Use sterile, nuclease-free consumables. It is recommended to aliquot the reconstituted DNA into single-use portions before freezing, to prevent degradation caused by repeated freeze-thaw cycles and to avoid nuclease contamination.
    4. Experimental Suitability:This product is suitable for common molecular biology applications such as PCR, qPCR, restriction enzyme digestion, and library construction. If the downstream assay is sensitive to inhibitors, ensure that the DNA solution is free of residual ethanol or high-concentration salt interference.
    5. Intended Use Statement:The product is for research use only and is not intended for clinical diagnostic purposes.

Ordering & shipping

  • Minimum order: 1 unit
  • Lead time: varies with order quantity and specifications. Please consult your local distributor or our sales team for confirmation
  • Payment: T/T 100% in advance; PayPal; Alibaba Trade Assurance
  • Shipping: FedEx / DHL / UPS express; cold-chain packing available on request
  • Price: USD; specification / size is listed on this page

Partial purchase records (0)

No one bought this product
Total 0 records, divided into1 pages. First Prev Next Last

Leave a message

* To protect against spam, please pass the CAPTCHA test below.

Newsletter

Sign up
0 0