Home > Molecular Biology > Genomic DNA(gDNA) > Genomic DNA from Bacillus cereus

Genomic DNA from Bacillus cereus

Genomic DNA from Bacillus cereus
Total $206

Product Summary

Alias:蜡样芽孢杆菌基因组DNA

NO.:SLQC16189

Lead time:1-4days

Product Form:Lyophilized powder;5μg/Vial

concentration:50ng/μL

    Number:

Details

Bacillus cereus Genomic DNA - Basic Information

Storage Conditions 2-8°C
Procedure Before use, add anhydrous ethanol to Buffer GD and Wash Solution PW; refer to the bottle labels for the volume to add;
1. Take 1-5 ml of bacterial culture, centrifuge at 10,000 rpm (11,500×g) for 1 min, and remove the supernatant as thoroughly as possible;
2. Add 200 μL Buffer GA to the pellet, and vortex until the pellet is completely resuspended. Note: For Gram-positive bacteria with tough cell walls, skip step 2 and perform cell wall digestion using lysozyme solution. Specific method: Add 110 μL buffer (20 mM Tris, pH 8.0; 2 mM Na2-EDTA; 1.2% Triton) and 70 μL lysozyme solution (50 mg/mL, prepared by the user, Cat. No.: RT401), and incubate at 37°C for over 30 min. If RNA removal is required, add 4 μL RNase A (100 mg/mL) solution (prepared by the user, Cat. No.: RT405-12), vortex for 15 sec, and let stand at room temperature for 5 min;
3. Add 20 μL Proteinase K solution to the tube and mix well;
4. Add 220 μL Buffer GB, vortex for 15 sec, and incubate at 70°C for 10 min. The solution should become clear. Briefly centrifuge to remove droplets from the lid. Note: A white precipitate may form when Buffer GB is added, which usually disappears during incubation at 70°C and does not affect subsequent steps. If the solution does not become clear, it indicates incomplete cell lysis, which may result in low DNA yield and impure extracted DNA;
5. Add 220 μL anhydrous ethanol, vortex thoroughly for 15 sec. A flocculent precipitate may appear at this stage. Briefly centrifuge to remove droplets from the lid;
6. Transfer the solution and any precipitate from the previous step into a CB3 adsorption column (placed in a collection tube), centrifuge at 12,000 rpm (13,400×g) for 30 sec, discard the waste liquid, and place the CB3 column back into the collection tube;
7. Add 500 μL Buffer GD to the CB3 adsorption column (ensure anhydrous ethanol has been added before use), centrifuge at 12,000 rpm (13,400×g) for 30 sec, discard the waste liquid, and place the CB3 column back into the collection tube;
8. Add 600 μL Wash Solution PW to the CB3 adsorption column (ensure anhydrous ethanol has been added before use), centrifuge at 12,000 rpm (13,400×g) for 30 sec, discard the waste liquid, and place the CB3 column back into the collection tube;
9. Repeat step 8;
10. Place the CB3 column back into the collection tube, centrifuge at 12,000 rpm (13,400×g) for 2 min, and discard the waste liquid. Leave the CB3 column at room temperature for several minutes to completely dry any residual wash solution from the adsorption material. Note: This step removes residual wash solution from the column. Residual ethanol in the wash solution can interfere with subsequent enzymatic reactions (e.g., restriction digestion, PCR);
11. Transfer the CB3 column into a clean centrifuge tube, and add 50-200 μL Elution Buffer TE dropwise to the center of the adsorption membrane. Let stand at room temperature for 2-5 min, then centrifuge at 12,000 rpm (13,400×g) for 2 min to collect the solution in the centrifuge tube. Note: The volume of Elution Buffer should not be less than 50 μL, as smaller volumes reduce recovery efficiency. The pH of the elution buffer significantly affects elution efficiency. If using ddH2O as the eluent, ensure its pH is within 7.0-8.5; a pH below 7.0 reduces elution efficiency; DNA products should be stored at -20°C to prevent degradation. To increase genomic DNA yield, the collected solution can be reapplied to the CB3 column, allowed to stand at room temperature for 2 min, and then centrifuged at 12,000 rpm (13,400×g) for 2 min;
Sharing Method Public Welfare Sharing

? Notes:

    1. Storage Conditions:Lyophilized powder should be stored at 2–8°C away from light. After reconstitution or for solution-type products, store at –20°C and avoid repeated freeze-thaw cycles. For short-term frequent use (within 1 week), temporary storage at 4°C is acceptable.
    2. Reconstitution Method:Prior to use, briefly centrifuge the lyophilized powder (e.g., 12,000 rpm for 1 minute) to collect the DNA at the bottom of the tube. It is recommended to dissolve in sterile TE buffer (pH 8.0) or sterile ddH₂O (pH 7.0–8.5). Mix gently; avoid vigorous vortexing.
    3. Contamination Prevention:Gloves must be worn during operation. Use sterile, nuclease-free consumables. It is recommended to aliquot the reconstituted DNA into single-use portions before freezing, to prevent degradation caused by repeated freeze-thaw cycles and to avoid nuclease contamination.
    4. Experimental Suitability:This product is suitable for common molecular biology applications such as PCR, qPCR, restriction enzyme digestion, and library construction. If the downstream assay is sensitive to inhibitors, ensure that the DNA solution is free of residual ethanol or high-concentration salt interference.
    5. Intended Use Statement:The product is for research use only and is not intended for clinical diagnostic purposes.

Ordering & shipping

  • Minimum order: 1 unit
  • Lead time: varies with order quantity and specifications. Please consult your local distributor or our sales team for confirmation
  • Payment: T/T 100% in advance; PayPal; Alibaba Trade Assurance
  • Shipping: FedEx / DHL / UPS express; cold-chain packing available on request
  • Price: USD; specification / size is listed on this page

Partial purchase records (0)

No one bought this product
Total 0 records, divided into1 pages. First Prev Next Last

Leave a message

* To protect against spam, please pass the CAPTCHA test below.

Newsletter

Sign up
0 0