Home > Molecular Biology > Genomic DNA(gDNA) > Genomic DNA from Bacillus cereus

Genomic DNA from Bacillus cereus

Genomic DNA from Bacillus cereus
Total $284

Product Summary

Alias:蜡样芽孢杆菌基因组DNA

NO.:SLQC16223

Lead time:1-4days

Product Form:Lyophilized powder;5μg/Vial

Purity:1.79

    Number:

Details

Bacillus cereus Genomic DNA - Basic Information

Storage Conditions 2-8℃
Operating Procedure Please add absolute ethanol to Buffer GD and Wash Buffer PW before use. Refer to the label on the bottle for the volume to add.
1. Take 1-5 ml of bacterial culture, centrifuge at 10,000 rpm (11,500×g) for 1 min, and remove the supernatant as completely as possible.
2. Add 200 μL of Buffer GA to the bacterial pellet, and vortex until the bacteria are thoroughly suspended. Note: For Gram-positive bacteria with difficult-to-break cell walls, skip step 2 and instead add lysozyme solution for cell wall digestion. The specific method is: add 110 μL of buffer (20 mM Tris, pH 8.0; 2 mM Na2-EDTA; 1.2% Triton) and 70 μL of lysozyme solution (50 mg/mL, prepared by the customer, catalog number: RT401), and incubate at 37°C for over 30 min. If RNA removal is required, add 4 μL of RNase A solution (100 mg/mL, prepared by the customer, catalog number: RT405-12), vortex for 15 sec, and let stand at room temperature for 5 min.
3. Add 20 μL of Proteinase K solution to the tube and mix well.
4. Add 220 μL of Buffer GB, vortex for 15 sec, incubate at 70°C for 10 min until the solution becomes clear, and briefly centrifuge to remove water droplets from the inner wall of the tube cap. Note: A white precipitate may form when adding Buffer GB, which typically disappears during incubation at 70°C and will not affect subsequent experiments. If the solution does not become clear, it indicates incomplete cell lysis, which may result in low DNA yield and impure DNA extraction.
5. Add 220 μL of absolute ethanol, vortex thoroughly for 15 sec. A flocculent precipitate may appear at this point. Briefly centrifuge to remove water droplets from the inner wall of the tube cap.
6. Transfer the solution and flocculent precipitate from the previous step into an adsorption column CB3 (place the column in a collection tube), centrifuge at 12,000 rpm (13,400×g) for 30 sec, discard the flow-through, and place the adsorption column CB3 back into the collection tube.
7. Add 500 μL of Buffer GD to the adsorption column CB3 (ensure absolute ethanol has been added before use), centrifuge at 12,000 rpm (13,400×g) for 30 sec, discard the flow-through, and place the adsorption column CB3 back into the collection tube.
8. Add 600 μL of Wash Buffer PW to the adsorption column CB3 (ensure absolute ethanol has been added before use), centrifuge at 12,000 rpm (13,400×g) for 30 sec, discard the flow-through, and place the adsorption column CB3 back into the collection tube.
9. Repeat step 8.
10. Place the adsorption column CB3 back into the collection tube, centrifuge at 12,000 rpm (13,400×g) for 2 min, and discard the flow-through. Leave the adsorption column CB3 at room temperature for several minutes to thoroughly dry any residual wash buffer from the adsorption material. Note: This step aims to remove residual wash buffer from the adsorption column, as ethanol residues in the wash buffer can affect subsequent enzymatic reactions (e.g., restriction digestion, PCR).
11. Transfer the adsorption column CB3 into a clean centrifuge tube, add 50-200 μL of Elution Buffer TE dropwise to the center of the adsorption membrane, let stand at room temperature for 2-5 min, centrifuge at 12,000 rpm (13,400×g) for 2 min, and collect the solution into the centrifuge tube. Note: The volume of elution buffer should not be less than 50 μL, as a smaller volume will affect recovery efficiency. The pH of the elution buffer greatly influences elution efficiency. If using ddH2O as the eluent, ensure its pH is within the range of 7.0-8.5; a pH below 7.0 will reduce elution efficiency. DNA products should be stored at -20°C to prevent degradation. To increase genomic DNA yield, the collected solution can be reapplied to the adsorption column CB3, let stand at room temperature for 2 min, and centrifuge at 12,000 rpm (13,400×g) for 2 min.
Sharing Method Public Welfare Sharing

? Notes:

    1. Storage Conditions:Lyophilized powder should be stored at 2–8°C away from light. After reconstitution or for solution-type products, store at –20°C and avoid repeated freeze-thaw cycles. For short-term frequent use (within 1 week), temporary storage at 4°C is acceptable.
    2. Reconstitution Method:Prior to use, briefly centrifuge the lyophilized powder (e.g., 12,000 rpm for 1 minute) to collect the DNA at the bottom of the tube. It is recommended to dissolve in sterile TE buffer (pH 8.0) or sterile ddH₂O (pH 7.0–8.5). Mix gently; avoid vigorous vortexing.
    3. Contamination Prevention:Gloves must be worn during operation. Use sterile, nuclease-free consumables. It is recommended to aliquot the reconstituted DNA into single-use portions before freezing, to prevent degradation caused by repeated freeze-thaw cycles and to avoid nuclease contamination.
    4. Experimental Suitability:This product is suitable for common molecular biology applications such as PCR, qPCR, restriction enzyme digestion, and library construction. If the downstream assay is sensitive to inhibitors, ensure that the DNA solution is free of residual ethanol or high-concentration salt interference.
    5. Intended Use Statement:The product is for research use only and is not intended for clinical diagnostic purposes.

Ordering & shipping

  • Minimum order: 1 unit
  • Lead time: varies with order quantity and specifications. Please consult your local distributor or our sales team for confirmation
  • Payment: T/T 100% in advance; PayPal; Alibaba Trade Assurance
  • Shipping: FedEx / DHL / UPS express; cold-chain packing available on request
  • Price: USD; specification / size is listed on this page

Partial purchase records (0)

No one bought this product
Total 0 records, divided into1 pages. First Prev Next Last

Leave a message

* To protect against spam, please pass the CAPTCHA test below.

Newsletter

Sign up
0 0