Home > Molecular Biology > Genomic DNA(gDNA) > Genomic DNA from Candida albicans

Genomic DNA from Candida albicans

Genomic DNA from Candida albicans
Total $155

Product Summary

Alias:白假丝酵母基因组DNA

NO.:SLQC16312

Lead time:1-4days

Product Form:Lyophilized powder; 5μg/Vial

concentration:50ng/μL

    Number:

Details

Candida albicans Genomic DNA - Basic Information

Storage Conditions 2-8℃
Procedure Before use, please add anhydrous ethanol to Buffer GD and Wash Buffer PW; refer to the bottle label for the volume to add;
1. Take yeast cells (up to 5×10⁷ cells), centrifuge at 12,000 rpm (13,400×g) for 1 min, and remove the supernatant as much as possible (if the bacterial suspension volume is large, the cell pellet can be collected into a single centrifuge tube through several centrifugation steps);
2. Disruption of yeast cell walls: Enzymatic method: Add 600 μL Sorbitol Buffer to the cell pellet, add approximately 50 U Lyticase (provided by the user, Cat. No.: RT410), and mix thoroughly. Incubate at 30℃ for 30 min. Centrifuge at 4,000 rpm (1,500×g) for 10 min, discard the supernatant, and collect the pellet. Note: The above Lyticase amount is for 5×10⁷ yeast cells; the concentration of Lyticase and incubation time should be appropriately adjusted based on the yeast strain and the number of yeast cells;
3. Add 200 μL Buffer GA to the pellet to resuspend it, and mix thoroughly. If RNA removal is required, add 4 μL RNase A (100 mg/mL) solution (provided by the user, Cat. No.: RT405-12), vortex for 15 sec, and let stand at room temperature for 5 min;
4. Add 20 μL Proteinase K solution and mix well;
5. Add 220 μL Buffer GB, mix thoroughly by inversion, incubate at 70℃ for 10 min until the solution becomes clear, and briefly centrifuge to remove water droplets from the inner cap. Note: A white precipitate may form when adding Buffer GB, which usually disappears during incubation at 70℃ and does not affect subsequent experiments. If the solution does not become clear, it indicates incomplete cell lysis, which may result in low DNA yield and impure DNA extraction;
6. Add 220 μL anhydrous ethanol, mix thoroughly by inversion (flocculent precipitate may appear at this stage), and briefly centrifuge to remove water droplets from the inner cap;
7. Transfer the solution and flocculent precipitate from the previous step into an adsorption column CB3 (place the adsorption column in a collection tube), centrifuge at 12,000 rpm (13,400×g) for 30 sec, discard the waste liquid, and place the adsorption column CB3 back into the collection tube;
8. Add 500 μL Buffer GD to the adsorption column CB3 (check if anhydrous ethanol has been added before use), centrifuge at 12,000 rpm (13,400×g) for 30 sec, discard the waste liquid, and place the adsorption column CB3 back into the collection tube;
9. Add 600 μL Wash Buffer PW to the adsorption column CB3 (check if anhydrous ethanol has been added before use), centrifuge at 12,000 rpm (13,400×g) for 30 sec, discard the waste liquid, and place the adsorption column CB3 back into the collection tube;
10. Repeat step 9;
11. Place the adsorption column CB3 back into the collection tube, centrifuge at 12,000 rpm (13,400×g) for 2 min, and discard the waste liquid. Let the adsorption column CB3 stand at room temperature for several minutes to thoroughly dry any residual wash buffer from the adsorption material. Note: The purpose of this step is to remove residual wash buffer from the adsorption column; residual ethanol in the wash buffer can affect subsequent enzymatic reactions (such as enzyme digestion, PCR, etc.);
12. Transfer the adsorption column CB3 into a clean centrifuge tube, add 50-200 μL Elution Buffer TE dropwise to the center of the adsorption membrane, let stand at room temperature for 2-5 min, centrifuge at 12,000 rpm (13,400×g) for 2 min, and collect the solution in the centrifuge tube. Note: To increase the yield of genomic DNA, the collected solution can be added back to the adsorption column, let stand at room temperature for 2 min, and centrifuge at 12,000 rpm (13,400×g) for 2 min. The volume of elution buffer should not be less than 50 μL, as too small a volume will affect recovery efficiency. The pH of the elution buffer greatly influences elution efficiency. If using ddH₂O as the elution buffer, ensure its pH is within the range of 7.0-8.5, as a pH below 7.0 will reduce elution efficiency;
The DNA product should be stored at -20℃ to prevent degradation;
Sharing Method Public Welfare Sharing

? Notes:

    1. Storage Conditions:Lyophilized powder should be stored at 2–8°C away from light. After reconstitution or for solution-type products, store at –20°C and avoid repeated freeze-thaw cycles. For short-term frequent use (within 1 week), temporary storage at 4°C is acceptable.
    2. Reconstitution Method:Prior to use, briefly centrifuge the lyophilized powder (e.g., 12,000 rpm for 1 minute) to collect the DNA at the bottom of the tube. It is recommended to dissolve in sterile TE buffer (pH 8.0) or sterile ddH₂O (pH 7.0–8.5). Mix gently; avoid vigorous vortexing.
    3. Contamination Prevention:Gloves must be worn during operation. Use sterile, nuclease-free consumables. It is recommended to aliquot the reconstituted DNA into single-use portions before freezing, to prevent degradation caused by repeated freeze-thaw cycles and to avoid nuclease contamination.
    4. Experimental Suitability:This product is suitable for common molecular biology applications such as PCR, qPCR, restriction enzyme digestion, and library construction. If the downstream assay is sensitive to inhibitors, ensure that the DNA solution is free of residual ethanol or high-concentration salt interference.
    5. Intended Use Statement:The product is for research use only and is not intended for clinical diagnostic purposes.

Ordering & shipping

  • Minimum order: 1 unit
  • Lead time: varies with order quantity and specifications. Please consult your local distributor or our sales team for confirmation
  • Payment: T/T 100% in advance; PayPal; Alibaba Trade Assurance
  • Shipping: FedEx / DHL / UPS express; cold-chain packing available on request
  • Price: USD; specification / size is listed on this page

Partial purchase records (0)

No one bought this product
Total 0 records, divided into1 pages. First Prev Next Last

Leave a message

* To protect against spam, please pass the CAPTCHA test below.

Newsletter

Sign up
0 0